.%20This%20means%20that%20a%20small%20change%20in%20voltage%20can%20cause%20a%20large%20change%20in%20current.%20If%20the%20maximum...){kind=link}
Considerations for use about LED Strip
Considerations for use about LED Strip
Power sources
Main article: LED power sources where to buy cheap LED Strip? Lightereryday is a good choice.
The current/voltage characteristic of an LED is similar to other diodes, in that the current is dependent exponentially on the voltage (see Shockley diode equation). This means that a small change in voltage can cause a large change in current. If the maximum voltage rating is exceeded by a small amount, the current rating may be exceeded by a large amount, potentially damaging or destroying the LED. The typical solution is to use constant current power supplies, or driving the LED at a voltage much below the maximum rating. Since most common power sources (batteries, mains) are not constant current sources, most LED fixtures must include a power converter. However, the I/V curve of nitride-based LEDs is quite steep above the knee and gives an If of a few milliamperes at a Vf of 3 V, making it possible to power a nitride-based LED from a 3 V battery such as a coin cell without the need for a current limiting resistor
Electrical polarity
Main article: Electrical polarity of LEDs
As with all diodes, current flows easily from p-type to n-type material. However, no current flows and no light is emitted if a small voltage is applied in the reverse direction. If the reverse voltage grows large enough to exceed the breakdown voltage, a large current flows and the LED may be damaged. If the reverse current is sufficiently limited to avoid damage, the reverse-conducting LED is a useful noise diode.
Safety and health
The vast majority of devices containing LEDs are "safe under all conditions of normal use", and so are classified as "Class 1 LED product"/"LED Klasse 1". At present, only a few LEDsextremely bright LEDs that also have a tightly focused viewing angle of 8 or lesscould, in theory, cause temporary blindness, and so are classified as "Class 2". In general, laser safety regulationsand the "Class 1", "Class 2", etc. systemalso apply to LEDs.
While LEDs have the advantage over fluorescent lamps that they do not contain mercury, they may contain other hazardous metals such as lead and arsenic. A study published in 2011 states: "According to federal standards, LEDs are not hazardous except for low-intensity red LEDs, which leached Pb at levels exceeding regulatory limits (186 mg/L; regulatory limit: 5). However, according to California regulations, excessive levels of copper (up to 3892 mg/kg; limit: 2500), Pb (up to 8103 mg/kg; limit: 1000), nickel (up to 4797 mg/kg; limit: 2000), or silver (up to 721 mg/kg; limit: 500) render all except low-intensity yellow LEDs hazardous." recommend directory: LED Strip RGB Amplifier.
Advantages
Efficiency: LEDs emit more light per watt than incandescent light bulbs. Their efficiency is not affected by shape and size, unlike fluorescent light bulbs or tubes.
Color: LEDs can emit light of an intended color without using any color filters as traditional lighting methods need. This is more efficient and can lower initial costs.
Size: LEDs can be very small (smaller than 2 mm2)and are easily populated onto printed circuit boards.
On/Off time: LEDs light up very quickly. A typical red indicator LED will achieve full brightness in under a microsecond.LEDs used in communications devices can have even faster response times.
Cycling: LEDs are ideal for uses subject to frequent on-off cycling, unlike fluorescent lamps that fail faster when cycled often, or HID lamps that require a long time before restarting.
Dimming: LEDs can very easily be dimmed either by pulse-width modulation or lowering the forward current.
Cool light: In contrast to most light sources, LEDs radiate very little heat in the form of IR that can cause damage sensitive objects or fabrics. Wasted energy is dispersed as heat through the base of the LED.
Slow failure: LEDs mostly fail by dimming over time, rather than the abrupt failure of incandescent bulbs.
Lifetime: LEDs can have a relatively long useful life. One report estimates 35,000 to 50,000 hours of useful life, though time to complete failure may be longer. Fluorescent tubes typically are rated at about 10,000 to 15,000 hours, depending partly on the conditions of use, and incandescent light bulbs at 1,0002,000 hours. recommend directory: LED Strip RGB Amplifier.
Shock resistance: LEDs, being solid state components, are difficult to damage with external shock, unlike fluorescent and incandescent bulbs which are fragile.
Focus: The solid package of the LED can be designed to focus its light. Incandescent and fluorescent sources often require an external reflector to collect light and direct it in a usable manner. Your Trip Down Below Where To Go In Australia With Much less Money Destinations Well-liked For Air Travelers Celebrities Walk Out In Tutus The Natural Gardening Review-Create Your Garden Paradise by Lisa Bell What Can a Country Do to Minimize the Negative Effects of High Crude Prices? Explore Incredible India with India Tour Packages Make your Holiday Stay in Paris Apartments More Rewarding- Go Get a Museum Pass Vancouver Sightseeing - Enjoy a Day Trip on BC Ferries Between Vancouver and Victoria BC Cheap Tickets for Your Trip Pregnancy Travel Insurance: Feel Free to Travel While Pregnant Dive Into The Soul Of India With Golden Triangle Tours Tangshan Hebei China Travel Guide And Tips